Taylor Frozen Dessert Maker Model 161 User Manual

Model 161Soft Serve FreezerOriginal Operating Instructions055155-M 8/14/08 (Original Publication)(Updated 5/29/12

6Model 161SafetyS DO NOT allow untrained personnel tooperate this machine.S DO NOT put objects or fingers in doorspout.S DO NOT operate the freezer un

7Model 161 Operator Parts IdentificationSection 4 Operator Parts IdentificationModel 161Figure 1ITEM DESCRIPTION PART NO.1 PAN-DRIP *161* 0552062 PANE

8Model 161Operator Parts Identification120501Beater Door AssemblyFigure 2ITEM DESCRIPTION PART NO.1 DRAW VALVE 0247632 O--RING 7/8 OD X .103 W 0144023

9Model 161 Operator Parts Identification110727AccessoriesFigure 3ITEM DESCRIPTION PART NO.1 PAIL-6·QT. 0233482 BRUSH-REAR BRG 1” D X 2” L G 0130713 BR

10Model 161Important: To the OperatorSection 5 Important: To the OperatorFigure 4ITEMDESCRIPTION1 POWER SWITCH2 MIX REFRIGERATION KEY3 STANDBY KEY4 WA

11Model 161 Important: To the OperatorPower SwitchWhen placed in the ON position, the power switchallows Softecht control panel operation.MIX REFWhen

12Model 161Important: To the OperatorIf the beater motor is turning properly, press the WASHkey to cancel the cycle. Press the AUTO key on bothsides o

13Model 161 Operating Procedures120529Section 6 Operating ProceduresThe Model 161 is a soft serve counter model with athree spout door. Two individual

14Model 161Operating Procedures120501Step 3Place the large o--rings into the grooves on the back ofthe machine door and lubricate.Figure 9Step 4Slide

15Model 161 Operating ProceduresStep 9Slide the two o--rings into the grooves on the remainingdraw valves and lubricate.Figure 13Step 10Lubricate the

Complete this page for quick reference when service is required:Taylor Distributor:Address:Phone:Service:Parts:Date of Installation:Information found

16Model 161Operating ProceduresStep 13Snap the design caps over the bottom of the freezerdoor spouts.Figure 17Step 14Lay the feed tubes in the bottom

17Model 161 Operating ProceduresStep 3While the solution is flowing into the freezing cylinder,brush clean the mix hopper, the mix inlet hole, and the

18Model 161Operating Procedures080925PrimingPrime the machine as close as possible to the time offirst product draw.Step 1With a pail beneath the door

19Model 161 Operating ProceduresRinsingStep 1Pour one gallon (3.8 liters) of cool, clean water into themix hopper. With the brushes provided, scrub th

20Model 161Operating ProceduresStep 3From the freezer door, remove design caps, pivot pins,draw handles, and draw valves. Remove all o--rings.Note: To

21Model 161 Important: Operator ChecklistSection 7 Important: Operator ChecklistDuring Cleaning and SanitizingALWAYS FOLLOW L OCAL HEALTH CODES.Cleani

22Model 161Important: Operator Checklistj 5. If your machine is air cooled, check thecondenser for an accumulation of dirt and lint.A dirty condenser

23Model 161 Troubleshooting GuideSection 8 Troubleshooting G uidePROBLEM PROBABLE CAUSE REMEDY PAGEREF.1. No product beingdispensed.a. The power switc

24Model 161Troubleshooting GuidePROBLEM PROBABLE CAUSE REMEDY PAGEREF.4. The product is too soft. a. The control is set toowarm.a. Contact servicetech

25Model 161 Troubleshooting GuidePROBLEM PROBABLE CAUSE REMEDY PAGEREF.9. The unit goes out onoverload excessively.a. There are too manyappliances plu

Table of Contents Model 161Table of ContentsSection 1 To the Installer 1...Installer Safety 1...

26Model 161Parts Replacement Schedule120501Section 9 Parts Replacement SchedulePART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY.Beater Driv

Section 10 Parts List27+ Available SeparatelyModel 161 Parts List110829DESCRIPTION PARTNUMBERQTY. W ARR.CLASSREMARKSACTUATOR-SWITCH-PLASTIC 035609 2 1

+ Available Separately28Parts List Model 161DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBER+GROMMET-COMPRESSOR MT. 037428 4 000+SLEEVE-MOUNTING-COMP. 039

29+ Available SeparatelyModel 161 Parts List120501DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBER+SEAL-DRAW VALVE *SMALL H-RING 030930 1 000DRYER-CAP. TU

+ Available Separately30Parts List Model 161DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBERLABEL-CAUTION-GRD-PERM 032164 1 000LABEL-DOOR-MOVE PART 032749

31+ Available SeparatelyModel 161 Parts List120501DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBERPULLEY-5.7" PITCH DIA X 5 041498 2 103PULLEY-AK20X5

+ Available Separately32Parts List Model 161DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBERTERMINAL-LOW VOLTAGE GROUND 034455 2 000TRAY-DRIP 16-7/8L 0201

33+ Available SeparatelyModel 161 Parts ListDESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBER50HZ (STANDARD-ROHS) -40 220-240V 50HZ 1PHBLOCK-TERMINAL 7P GR

+ Available Separately34Parts List Model 161DESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBERMARINE USEBLOCK-TERMINAL 7P GREEN 024156 1 105DIAGRAM-WIRING *

35+ Available SeparatelyModel 161 Parts ListDESCRIPTION REMARKSW ARR.CLASSQTY.PARTNUMBERFORM-QUALITY REPORT BY FAX 065712-SCH 1GEAR A.*REDUCER 4 TO 1

Model 161 Table of ContentsTable of Contents -- Page 2Section 7 Important: Operator Checklist 21...During Cleaning and Sani

Model 161063820-27SRev. 2/10

Model 161063820-40SRev. 2/10

1Model 161 To the Installer081208Section 1 To the InstallerThe following are general installation instructions. Forcomplete installation details, plea

2Model 161To the Installer101012Water Connections(Water Cooled Units Only)An adequate cold water supply must be provided witha hand shut--off valve. O

3Model 161 To the Installer120529Electrical Hook--Up Installation(60 Cycle, 1 Ph, Supplied With Cord and Plug)This freezer is supplied with a 3--wire

4Model 161To the OperatorSection 2 To the OperatorThe Model 161 soft serve freezer has been carefullyengineered and manufactured to give you dependabl

5Model 161 Safety110301Section 3 SafetyWe, at Taylor Company, are concerned about thesafety of the operator when he or she comes in contactwith the fr